For a job well done, you must properly prepare the wooden surface and apply the product according to the rules of art. Here is some useful information to give a youthful look to a wooden deck.
How often do you repaint or dye your wooden deck? It depends on many factors including the orientation, the use you make of it and the severity of the bad weather. To find out if it's time to go there, do an inspection after the snow melts. Does the coating peel? Is there mold? Is the surface worn or discolored? If so, it's time to give it a layer of rejuvenation, otherwise, the deterioration of the wood will be fast. It is important, however, not to skip any step. The majority of patio decking problems are the result of inadequate preparation or an application made during inappropriate weather. You can find which deck stain will be useful for your wooden deck from https://prizedreviews.com/best-deck-stain/.
At first glance, check the weather forecast before applying the coating to ensure optimal installation conditions. Never apply the dye or paint under direct sunlight, which could affect the adhesion of the product and the uniformity of color. It is always better to do it in the shade or in cloudy weather. In addition, the ambient temperature and surface temperature must be maintained between 10 ° C (50 ° F) and 32 ° C (90 ° F) for a period of 24 hours. In addition, terrace dyes should be applied when the relative humidity is between 40 and 70%. Relatively high relative humidity may affect the drying time, as well as the gloss.
In fact, the drying time indicated by the manufacturer corresponds to the expected time under normal conditions, i.e. a temperature of 21 ° C (70 ° F) and a relative humidity of 40%. It can, therefore, vary if these conditions change. Also, do not go to work if you expect rain, dew or frost in the next three days. The layer adheres poorly to damp or wet wood. Finally, the wood itself must be very dry. Its moisture content must not exceed 15%. When in doubt, use a wood hygrometer that accurately measures the moisture content of the wood.
Is the weather nice and you're ready to take action? Do not immediately dip your brush into the paint or stain container. You must first make sure that the surface is ready. If the wood is stained, dirty, scaly, damaged or has mold, you will have to eliminate these problems if you want to give it a nice appearance and extend the coating. To do this, there is a range of wood products including cleaners, renovators, regenerators, and strippers. Ask your retailer about the usefulness of using these products. It is important to seek advice for the preparation of the work.
If there is already a coating, take the time to check if the new layer will adhere well to the old one. First, that of the drop of water and then just spray a few drops of water at random on different sections of the terrace. If water is beading on the surface, leave the wood exposed longer to the weather, or sand it lightly before applying the stain or paint. On the other hand, if the water is quickly absorbed, you can proceed with confidence. There is also the test of "adhesive tapes". Apply the new coat on a small, inconspicuous section and allow drying for 24 hours. To check for adhesion, firmly press the end of an adhesive tape onto the freshly coated surface. Remove the tape in a fast, dry motion. If the tape is clean, the layer is in place and it is not necessary to remove the old one.
On the other hand, if the new layer adheres to the adhesive tape or if all the old coating is torn off the tape, you will need to strip or sand the entire surface. In some cases, it may be useful to apply a primer. Ask a painting specialist for advice. Finally, remember that it is possible to paint a tinted surface, but not the other way around. It may be helpful to apply a primer.
An effective method
The brush is the best tool to extend a deck covering. In order to obtain good results, it is advisable to use a brush with natural bristles for the oil layers and a brush with synthetic fibers (nylon) for the acrylic layers. If you opt for roller application, we suggest brushing the brush on the sides to ensure a good impregnation of the coating.
We also recommend applying a layer of the product over all surfaces of the wood - when possible - with particular attention to the end of the wood grain. Absorption of moisture by the end grain leads to cleavage of the fibers, which can cause problems on the coatings.
To reduce dye or paint streaks, slide the paintbrush in the direction of the wood grain and cover the board the entire length of the deck. Then go to the next board. Tip: Let the surface dry for at least 48 hours before stepping on it and wait at least 30 days before washing to allow the new coating to harden.
Finally, take care to buy enough products to treat the entire surface. But if you ever need more than one container of the same color to cover an entire section, make sure that it comes ideally from the same batch. A small trick to maintain the uniformity of the color: when it remains only a quarter of the product in the container, transfer the new color in this one and stir to mix the two. And, of course, do not forget to brew the product a few times during use.
