All central heating home systems are complicated; something that many people would not want to intervene with. But eventually, there comes a point where you find yourself in a situation where you are bound to remove your radiator for one reason or the other. Especially when Homeowners and Landlords are thinking of redecorating their property, repainting their walls, or changing the whole attire of the house.
It can simply be because you decided you want to repaint your walls. In case you decide to change the shade of the walls, you will have to remove the radiator. It might look like a job where you will need the extraneous help, but honestly, you do not need any special skills to pull off this job.
In this blog here, we will explain how to remove a radiator without draining the entire system.
Reasons Why Someone Would Want to Remove Their Radiator
1. The radiator might leak through pin holes left because of rust
2. You plan to redecorate the house and change the color of the walls.
3. You plan to replace the radiator because it is old now and decide to go for a new streamlined one.
The tools you will require removing a radiator:
• An Adjustable Spanner
• A Towel and sponges
• A Radiator Bleed Key
• And a Pair of adjustable Grips
What Type of Heating System Have You Got?
If you are not sure of the type of radiator you have, you can always check for a little dial on the front of your boiler. It should be located somewhere in the loft or your airing cupboard.
Do not forget where the dial is pointing at. You must keep it in mind once you finish up the job and put your old radiator back. That is because you are going to need to depressurize the system. And, add a small amount of inhibitor to it. If you have got a tank in the loft, you don’t need to worry about remembering where the system’s pressure is.
You can even check online for which radiator you carry or take the help of a professional. Because we do not want you hurting yourself while removing the radiator, make sure your tools are not worn out and you’ve got your gloves on.
The task to remove your radiator would take at least 30 to 40 minutes approximately. Not too much time spent if you follow the steps correctly.
How to remove the radiator without drowning the entire system?
Now that you have all your tools with you. And you have looked at your heating system, you can finally get down to business and carefully remove the radiator without drowning the system.
If you are still not able to, there is no need to worry. 247 Home Rescue is giving out boiler plans for Landlords and Homeowners on the best price rates possible!
With Free Annual Service, and 247 Home Rescue’s certified engineers, you can get anything fixed or repaired in no time. They have specified Homeowner and Landlord Boiler Plans, that can help you obtain some of the best deals for your Home and Safety!
In case you do it yourself, follow these simple steps here.
1. Shut Down the radiator valves:
• Shut off the lock-shield and the TRV, they are on the opposite ends of the radiator.
• Turn it towards the right and shut the valve off.
• Now undo the valve radiator bleed key. Make sure no water comes out. Occasionally a bit of water will drip as the pressure disintegrates, but It will eventually stop.
2. Drain the radiator:
• With the help of an adjustable spanner grip the valve and loosen the nut. You will get a little water running straight out.
• Wait for all the water to drain out. Keep a bucket close to your side. Even if there is a leak, the towels underneath will soak up the water.
3. Pull the valve off:
• If you think your radiator’s pipe has got enough stretch, you can pull the valve off and get the water to come out a lot faster.
4. Remove the radiator from its brackets:
• There are many sorts of radiator brackets, see which one you have.
• Before removing the radiator, loosen off the other end.
• Undo it completely. The same way you did it with the previous pipe.
• The extraneous water will come out itself. Use a towel or a mop to get rid of that.
• Bleed the radiator once again just in case there are not any more spills.
5. Tilt the side of the radiator:
• We tilt the side of the radiator so any excess water trapped at the bottom of the radiator can easily come out.
• Drain it completely.
• You will have to sit there for at least 5 to 10 minutes holding the radiator up at an angle.
• Once it is drained, pop it off the clips.
• Now you are ready to paint behind the radiator if that is the plan.
6. Fit the radiator back after painting your walls:
• To put the radiator back, you will simply have to reverse the entire process
• Fit the radiator back onto the clips and attach your pipes back on.
• Then, open the valves, bleed that excess air out, and fill up the radiator again.
• Make sure it tops the pressure up, standing accurate.
The guidelines are much more beneficial for Landlords for monthly maintenance. But because sometimes a single person cannot take on the workload of all the properties they own.
They must have a management set up, or packages that help someone else take care of their mess for them. This is where 247 Home Rescue comes in. They provide some of the best deals on landlord boiler plans and some of the best Gas-safe, certified engineers working around the clock for help and support.
Landlord Boiler plans are extremely essential for those individuals that own a lot of property in different areas of the UK and are looking for monthly/ yearly aid.
In Conclusion:
Before you start with the process, make sure you are aware of what you are dealing with. It may become daunting for those that do not know of how to deal with radiators, change or remove them, and lastly bleed them out.
If you still do not understand the process itself and feel that it might be difficult for you to take it on all by yourself. There is nothing to worry about. 247 Home Rescue has got some of the most brilliant, Gas Safe, certified specialists working around the clock for your safety and help.
