In recent times, I have discussed quite a lot about choosing the right amount of flashing tape. However, another element which needs to be addressed about is the installation. These days, every other manufacturer out there is following a particular set of instructions which must be adhered to follow the warranty of the product.
This may sound less complicated but to tell you the truth, not a single procedure about it is available on the internet. The guidelines might circumspect in between the manufacturers, making the job of the contractors challenging and questionable. According to the Residential Code International, the windows should be flashed and fixed as per the requirements and demands of the manufacturers.
If any problem is being observed, the job was done under the consent and law of the building code, and you are not held accountable for it.
Whenever we talk about consuming the flashing tape (Non-Woven Adhesive Tape, Zebra Crossing Tape, HDPE Adhesive Tape) with temperatures, installations, and affinity of the materials is crucial, mostly on the materials which are bonded difficultly. With that being said, I will be discussing some of the most basics for you to understand and gain information about flashing tapes and how to install them wisely.
1) Substrates:
Every manufacturer out there identifies the kind of products which are reliable to bond and the products which demand your attention. To be fair, plywood, metal, solid wood, and vinyl work efficiently as long as they are adequately maintained and cleaned regularly. They should be protected from dust, oil, and dirt.
There are plenty of other manufacturers out there that propose that masonry, concrete, and OSB will deliver optimum results as soon as they are prepared accurately, while others might suggest that almost all the substrates should be loaded for optimum performance, especially in freezing conditions.
Keeping all the above points in mind, it’s essential to remember that priming is just a single solution; and therefore it is highly advised to all the manufacturers and industrialists out there to select the right tape for their object which will reduce their chances of using the primer and labor.
2) Temperature:
Time and time again, it has been said that heat and weather plays an integral role in the process of installation. What’s the reason behind it? The answer is simple and easy to understand. Skilfully remodeled bitumen based products that don’t interact well in cold weather. Most of the products decrease their bonding intensity at around 50 degrees and might not even stick below 40 degrees. Some of the tapes are Herringbone Tapes, Fastener Tape, and Nylon Elastic Tape, etc.
The exception can be made only if you are working with a tape designed primarily for lower temperatures. In this case, an acrylic or butyl based products are considered as the most viable options in extreme conditions.
Cold weather and extreme conditions could be a challenge for many. For instance, standard reconstructed bitumen can exude at high temperatures, especially when they are attached and bonded under metal and stay unprotected to the sunlight. The best example which I can think of right now is of west-south facing windows and under metal floorings.
Butyl tapes (Tamper Evident Tape, Jacquard Elastic Tapes, Cotton Insulation Tapes) in this regard are quite steady at high temperatures but also have increased limits. Unless the tapes are designed perfectly to stay attached and well-protected in high temperatures and labeled properly, flashing tapes will start to alleviate at temperatures between 120 degrees to 180 degrees.
Some temperatures which are purposely high for commercial use can absorb temperatures worth 200 degrees and are not that tacky and challenging to find and work. If the manufacturer is unable to publicize the increasing temperature value, it is the responsibility of the labor and industrialists to ask for alternatives if they are short on the required products.
3) Shingle:
According to a report provided by building advisor, you can never go wrong by adopting the most common principles for the shingle. Understanding all the possible prospects that may tarnish and effect the long existence of the adhesive bond, the best thing you can do is to not completely depend on a joined tape that is preventing the water to stay out of the house.
All the crucial details, be it adhesive or not, should follow the old-age shingle principle. By using this approach, the material which is on the upper side is most of the times overhauled by the lower material making way for the water to flow down naturally and far away from the structure of the building if the adhesive fails to perform its job efficiently. Those rubber based adhesives are Packing Sealing Adhesive Tapes, Identification Tape, Knitted Tape, Cotton Elastic Tape,Braided Elastic Tape and Velvet Tape etc.
Related Articles :
Stucco Tape - The Best Tape Out in the Market
